Home injectables Anabolic Steroids Winstrol 50mg/Ml Injectable Oils for Muscle Growth
Winstrol 50mg/ml

Anabolic Steroids Winstrol 50mg/Ml Injectable Oils for Muscle Growth

Category: .


Winstrol / Stanozolol is hard to dissolvein normal solvents with a melting point of 242 Celsius. Winstrol / Stanozolol is commonly made into water suspension and oil form @ 50 mg/ml. We find wisntrol / stanozolol readily suits two well-intended purposes; enhancing overall athletic performance and as a cutting agent for the dieting bodybuilder or gym rat.



Data of Winstrol Suspension 50 mg/ml:
Winstrol Stanozolol 50 mg/ml Water Suspension
Affective chemical: Stanozolol.
Solvents: benzyl alcohol & benzyl benzoate
Carrier: PS80, Distilled water



Winstrol common recipe for 1000ml @ 50mg/ml
50 g stanozolol powders
240 ml BB 24%, 20 ml BA 2%
30 ml polysorbate 80 3%
635 ml distilled water (only)
Mix powder, BB, BA, and poly and heat until dissolved. filter, add water and re-filter.



Stanozolol / Winstrol for Bulking and Cutting


To gain muscle mass (bulking), Winstrol is best combined with a stronger androgen, such as Testosterone. This will give the cycle a good anabolic effect while minimizing estrogenic activity. This results in excellent increases in lean muscle mass, as opposed to the more common bulking cycle which greatly increases muscle mass while also increasing water retention and some gains in fat.
To lose fat (cutting), Winstrol is best combined with a non-aromatizing androgen such as Trenbolone or Halotestin. This combination can create a strongly defined, hard look. This is a very attractive look sought out by many bodybuilders.


The normal dosage for men is between 25-50 mg per day for the injectable version of Winstrol (40-70 mg per day for the tablets version). Winstrol is often combined with other steroids depending on the personal goals of the athletes.
We offer bulk batches of steroid oil or water conversions and professional assistance for steroid injectables productions. Only after you filtrate the oil conversions by .22 micron filters, then they will be finished injectables.
Stanozolol is much milder than this androgen in nature.


Stanozolol is a derivative of dihydrotestosterone, although its activity is much milder than this androgen in nature. It is technically classified as an anabolic steroid, shown to exhibit a slightly greater tendency for muscle growth than androgenic activity in early studies. While dihydrotestosterone really only provides androgenic side effects when administered, stanozolol instead provides quality muscle growth.


Admittedly the anabolic properties of this substance are still mild in comparison to many stronger compounds, but it is still a reliable builder. Its efficacy as an anabolic could even be comparable to Dianabol, however Winstrol / Stanozolol does not carry with it the same tendency for water retention. Stanozolol also contains the same c17 methylation we see with Dianabol, an alteration used so that oral administration is possible. To spite this design however, there are many injectable versions of this steroid produced.


Stanozolol: A favorable steroid to use during cutting cycles.


Structurally stanozolol is not capable of converting into estrogen. Likewise an antiestrogen is not necessary when using this steroid, gynecomastia not being a concern even among sensitive individuals. Since estrogen is also the culprit with water retention, instead of bulk Winstrol produces a lean, quality look to the physique with no fear of excess subcutaneous fluid retention. This makes Stanozolol a favorable steroid to use during cutting cycles, when water and fat retention are a major concern. It is also very popular among athletes in combination strength/speed sports such as Track and Field. In such disciplines one usually does not want to carry around excess water weight, and may therefore find the raw muscle-growth brought about by Winstrol quite favorable over the lower quality mass gains of more estrogenic agents.